SYRINGE, s.u., Luer, 50-60 ml

STD SINSSYDL60-

Valid Article

Former Code(s): SINSSYDF60L SINSZYN1005
The product is supplied (and stored) sterile, it must remain sterile until its use. Sterile = state of being free from all living microorganisms.
Single use
A single-use device, also referred to as a disposable device, is intended for use on one patient during a single procedure. It is not intended to be reprocessed (i.e., cleaned and disinfected or sterilized).
CE marking: declaration that the product meets EU standards for health, safety, and environmental protection. The CE marking indicates that the product may be sold freely in any part of the European Economic Area, regardless of its country of origin.
A02010201 - Infusion and irrigation syringes, luer cone, single-use
European Medical Device Nomenclature (EMDN) is the nomenclature of use by manufacturers when registering their medical devices in the EUDAMED database. EMDN is characterised by its alphanumeric structure that is established in a seven-level hierarchical tree.
In Europe, medical material that fulfills the definition of a medical device according to the MDR (Medical Device Regulation) is classified into 4 classes
OC subscriptions: included in supply or field order tools (e.g. UniField)
SC subscriptions: included in supply or field tools
OC validations: approved for procurement and use by an OC for international or local orders specifying context and activity in Medical Standard Lists (MSL)

This combination does not exist.

Add article to list

   

Add Kit To Wishlist

   

SYRINGE, Luer slip

Definition

A sterile device consisting of a calibrated barrel with plunger intended to be used for injection/withdrawal of fluids (e.g. medication) to/from a medical device or the body. At the distal end of the barrel is a male Luer connector for the attachment of the female connector (hub) of a hypodermic needle or an administration set.

Specifications

Image

Quality standards

ISO 7886-1, 2017, edition 2, (confirmed 2022) Sterile hypodermic syringes for single use - Part 1: Syringes for manual use

Technical specifications

  • BARREL: the reservoir for holding the liquid
    • transparent polypropylene / polyisoprene
    • capacity: 1 ml, 2 ml, 5 ml, 10 ml, 20 ml and 50-60 ml
    • scale markings are etched or printed on the barrel: in millilitres, easily readable
    • graduations: every 0.01 ml (1 ml syringe), every 0.1 ml (2 ml syringe), every 0.2 ml (5 ml syringe), every 0.5 ml (10 ml syringe) or every 1 ml (20 and 50 ml syringe)
    • with flanges: "wings" that jut out from the side of the syringe barrel. they provide an area or surface for the index finger and the middle finger to grasp during aspiration or administration.
    • with retaining ring (plunger backstop) to prevent accidental plunger rod withdrawal
    • ending with a male Luer tip: slip or push-on connection for a needle
  • PLUNGER: a piston-like device inside the barrel, designed for single-handed operation
    • polypropylene, polyethylene
    • perfectly fit to slide easily and smoothly inside the barrel
    • with thumb press: an area where one presses to push the plunger rod down into the barrel to expel contents.
    • plunger tip: the three part syringes end in a synthetic elastomer plunger tip or gasket, flat or dome shaped. This tip assures a perfect plunger barrel seal integrity and a flawless gliding behaviour. The gasket may be double-contact.
  • Sterile, for single use

Note: the 1 ml and 50/60 ml syringes are mostly 3-part syringes (including a gasket), the 2 ml, 5 ml, 10 ml and 20 ml syringes are also available as two-part syringes (without gasket). The barrel material of these two-part syringes often contains a lubricant allowing a smooth advancement of the plunger without the need of a rubber ring.

SEE TABLE BELOW

Packaging & Labelling

Unit sterile packaging in peel-open pack

Instructions for use

Single use syringes must be prepared immediately prior to injections since injectable preparations may contain solvents that corrode plastic (e.g. melarsoprol).

Some restricted information has been hidden. Sign in to see this information

Extra Tables

capacity

capacité

graduation

max. dead space

espace mort max.

Luer tip

embout Luer

1 ml0.01 ml0.07 ml

central cone

cône central

2 ml0.1 ml0.07 ml

central cone

cône central

5 ml0.2 ml0.075 ml

central cone

cône central

10 ml0.5 ml0.10 ml

Eccentric cone 

Cône excentrique

20 ml1 ml0.15 ml

Eccentric cone 

Cône excentrique

50 / 60 ml1 ml0.20 ml

Eccentric cone 

Cône excentrique