CHARGER-INVERTER (Victron EasySolar II) 48/230V 70A 5kVA

The Victron EasySolar-II GX 48/5000/70-50 MPPT 250/100 GX is an all-in-one solar power solution combining a 48 V 5000 VA inverter, a 70 A battery charger and a SmartSolar MPPT 250/100 solar charge controller in a single enclosure.

The integrated MultiPlus-II inverter converts 48 VDC battery voltage into 230 VAC pure sine wave output, suitable for sensitive electronic devices.

The integrated battery charger provides up to 70 A charge current for fast and efficient battery charging when AC input is available.

The built-in SmartSolar MPPT 250/100 controller allows direct connection of PV arrays up to 250 V open circuit voltage.

An integrated transfer switch (50 A) automatically switches between AC input and inverter output. In case of grid failure, the unit supplies connected loads without interruption.

The integrated GX device enables monitoring, configuration and remote management via VE.Bus, VE.Direct, Ethernet and Wi-Fi.

Features:

• true sine wave inverter
• integrated SmartSolar MPPT 250/100 charge controller
• adaptive 4-stage charging (bulk, absorption, float, storage)
• PowerControl and PowerAssist functions
• automatic transfer switch (50 A)
• parallel operation (up to 6 units)
• three-phase system configurable
• remote monitoring via VRM portal
• integrated GX device with display

INVERTER:

• input voltage range battery (DC): 38 – 66 V
• output voltage: 230 VAC ± 2 %, 50 Hz (adjustable to 60 Hz)
• continuous output power at 25 °C: 5000 VA (4000 W)
• continuous output power at 40 °C: 3700 W
• continuous output power at 65 °C: 3000 W
• peak power: 9000 W
• maximum efficiency: 96 %
• zero load power: 18 W
• zero load power in AES mode: 12 W
• zero load power in Search mode: 2 W

CHARGER:

• AC input voltage range: 187 – 265 VAC
• input frequency range: 45 – 65 Hz
• charge voltage thresholds (absorption/float): 57.6 / 55.2 V
• storage voltage: 52.8 V
• max. charge current: 70 A
• battery temperature sensor: yes

SOLAR CHARGE CONTROLLER:

• model: SmartSolar MPPT 250/100-Tr
• maximum output current: 100 A
• maximum PV power: 5800 W
• maximum PV open circuit voltage: 250 V
• maximum efficiency: 99 %
• self-consumption: 20 mA​

GENERAL:

• input: 1 AC
• outputs: 2 AC (AC-out-1 + auxiliary AC-out-2)
• programmable relay, function configurable
• VE.Bus communication port: for parallel and three phase operation, remote monitoring and system integration
• integrated GX device with Wi-Fi, Ethernet and VE.Direct
• remote control and configuration via VRM portal
• operating temperature: -20 to +45 °C (fan assisted cooling)
• PowerControl and PowerAssist functions, configurable
• transfer switch: 50 A

CONNECTORS:

• battery: M8 bolt connection
• PV input: M6 bolts
• AC connection: screw terminals 16 mm² (6 AWG)

PROTECTION:

• output short circuit
• overload
• battery voltage too high
• battery voltage too low
• temperature too high
• 230 VAC on inverter output
• input voltage ripple too high
• IP21, only for dry location

Read manual before use and installation. Further support documentation, including back-up sizing guidelines, can be found on your logistical knowledge base.

Configuration of the EasySolar-II GX is performed via the VE.Bus interface. For configuration using a computer, an MK3-USB interface is required together with Victron configuration software (e.g. VEConfigure).

The integrated GX device allows connection to a GX controller environment and to the Internet via Ethernet or Wi-Fi. This enables remote monitoring, system configuration and alarm management through the Victron VRM Portal.

Additional firmware-based functions (“Assistants”) can be configured using Victron software, including programmable relay logic, automatic generator start/stop and ESS functionality.